If the bracket screws are 2 inches long or shorter. Screws that come with the handrail mounting brackets might be too short to penetrate deep enough into the wall studs, and care must be taken to prevent cracked plaster. ![]() I wanted a happy place to put plants in my office. The combined thickness of three-coat plaster and lath can be 1 inch or more drywall is usually 3/4-inch-thick or less. Gold foil map / rainbow wall hanging / pink letter board Ready to see how my office shelves turned out?! office shelves So make sure to measure twice and drill once! Use a drill to create a pilot hole with a drill bit before inserting the anchor. I used these anchors/screws and they worked wonderfully! The down side of this option is that you’ll be putting a big hole in the plaster. anchors for plaster wallsįor the next option, you can use an anchor and screw designed for plaster. Either of these will help you find a stud so you can use a screw into the stud for hanging heavy things in plaster. I’ve also heard great things about Studpop2 since the magnet pops out when you get to a stud. I used the Stud Buddy and it was perfect for what I needed. This worked GREAT for me- even with the paneling over the lath and plaster (which I was worried would make it too think for the magnet to work). But, using a stud finder that is magnetic works like a charm since it sticks to the nails in the lath that are connected to the studs. Sadly, a traditional stud finder won’t work with plaster since it will just detect the lath, not the studs. If you’re going heavier, you’ll need special tools. European countries still plaster drywall (blueboard) as the standard. Plaster gave way to a thin coat of joint compound and finally nothing but tape). Since my plaster is covered in paneling, that’s what I’ve done so far. I would not use regular anchors, even though there is sheetrock behind your plaster (thats what sheetrock was invented for: replacing lathe, not plaster. If you’re going to hang something light in plaster, you can use a small screw or nail and it should be fine. So installing or using a picture rail is an option! Thus eliminating the need for making any holes in the walls. ![]() This is really the best answer for mounting something very heavy. Use plywood, attach plywood to wall studs. I have two bays of the wide shelves full of art books (6 shelves per bay) and they’re holding up just fine. You then connect wires to the picture rail from a hook and hang the art from the wire. Laths are actually very strong, I’m not sure why they’re so adamant it. This is a piece of trim that is attached to the studs higher up on the wall. Traditionally, homes with plaster walls had a picture rail. There are several ways in which to repair lath and plaster - using modern or traditional techniques, or by learning how to patch plaster.A post shared by Jenny Komenda on at 8:14am PDT If, on the other hand, large chunks of your wall or ceiling are coming away, more significant repair work will be necessary. Simply check them regularly and keep an eye on any new cracks that appear - often simply skimming over them with a suitable, lime-based, plaster mix is sufficient. Of course, if your walls are still in good condition, there is no need to touch them. If you live in a house with lath and plaster walls (likely if your house was built before 1940) then you might be wondering how to repair damaged lath and plaster. ![]() How do you Repair Lath and Plaster Walls? These mixtures usually used a 1:1:6 combination of gypsum or cement, lime putty and sharp sand for the initial two coats, then equal parts of lime putty and gypsum for the final layer. Later on, it became common to add in gypsum or sometimes cement - this was to speed up the setting process between each layer. The third layer was commonly made up of lime putty and a fine sand in a 3:1 mixture - or sometimes just lime putty. The first two layers of plaster that were applied to the lath were usually made up of lime putty and sharp sand in a 1:3 ratio - often with animal hair added in to help bind them. (Image credit: Getty) What Type of Plaster Was Used For Lath and Plaster? Lath and plaster walls were commonplace in house right up until the advent of plasterboard in the 1930s.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |